XFC-1100 vortex air pump

Don't judge new things with old perspectives. Technology is advancing too fast, so treat them rationally. A friend liked a XFC-1100 vortex air pump and asked me to do some research for him. Since he had just gotten into vortex air pumps and was a total novice, he was unsure and worried, so he asked me to give him a reference. I told them to go check out the details themselves, looking at the appearance and the internal parts that are easy to see. The friend still preferred a vortex air pump that had a long service life and was stable. I recommended this one, after all, I've been using it myself, so I know it well. Following my advice, he chose this XGB-7500 vortex air pump. I hope it meets his requirements.

Introduction

XFC-1100 vortex air pump is usually a horizontal pump product, such as a pipeline booster pump or a pipeline centrifugal pump. Its inlet and outlet are on the same horizontal line and directly connected to the conveying pipeline. The pipeline pump motor is located on the pump body. The inlet and outlet sizes of the pipeline pump are the same. There is a square base under the pump body, which can be conveniently installed on a concrete base. Small and lightweight pipeline pumps can also be directly supported and fixed by the inlet and outlet pipelines without a fixed base. But in this case, the pipelines at both ends of the pump must be supported and fixed. A pipeline booster pump refers to a pump installed in a pipeline to convey liquid. It is not limited to a certain type or shape of pump. It can be vertical or horizontal, such as vertical multistage centrifugal pumps. Horizontal multistage centrifugal pumps, vertical single-stage centrifugal pumps, horizontal single-stage centrifugal pumps, self-priming centrifugal pumps, etc., can all be called pipeline booster pumps. Generally speaking, a pipeline booster pump refers to a pump with a pipeline structure that can be directly connected in series as a pipeline.
Vortex air pump type selection
1. Impeller aerator. It has functions such as aeration, water stirring and aeration. It is suitable for aeration of large-area ponds with a water depth of more than 1m.
2. Waterwheel aerator. It has aeration and promotes water flow. It is suitable for ponds with relatively deep silt and an area of 1000~2500m².
3. Spray aerator. It has good aeration function, can quickly increase the dissolved oxygen in the surface water in a short time, and also has artistic appreciation. It is suitable for fish ponds in gardens or tourist areas.
4. Inflatable aerator. The deeper the water, the better, suitable for deep-water fish farming.
5. Jet aerator. Its aeration efficiency is higher than that of waterwheel type, inflatable spray and other aerators. It has a simple structure, can form water flow and stir the water body, and can gently aerate the water body without damaging fish. It is suitable for aeration of fish fry ponds.
6. XFC-1100 vortex air pump has the characteristics of being lightweight, easy to operate and having a single aeration function. It is suitable for fish fry cultivation ponds or greenhouse aquaculture ponds with a water depth of 0.7m and an area of less than 400m².

Maintenance
Replace the microporous tube immediately if it is found to be cracked.
If too much algae adheres and blocks the micropores, pat it lightly after drying to shake off the attachments, or soak it in 20% laundry detergent for 1 hour, clean it thoroughly and dry it before reuse.
Ensure that the power supply box does not leak electricity.
Perform regular lubrication and maintenance on the microporous aerator.
Prevent rust during the rainy season.
Prevent exposure to the sun during high temperature seasons, and a sunshade can be set up. If loose interfaces are found, fix them in time.
After the production cycle ends, disassemble the equipment and store it in the warehouse.
Daily maintenance:
1. Inspect the XGB-7500 vortex air pump every day.
2. Regularly check the inlet valve and air inlet valve. If leakage is found, repair it immediately.
3. Regularly check the tightness of the triangular belts on the vacuum pump pipelines and connections. If they are too loose or too tight, adjust them immediately.
4. Regularly check parts such as bearings and crossheads. If overheating occurs, perform maintenance.
5. Regularly check the tightness of the packing on the piston rod. If it is too loose, compress the packing plug, add packing or replace the packing. However, do not tighten the packing plug too tightly to avoid wearing the rod diameter.
6. Check the oil level every day. If it does not meet the specifications, adjust it to meet the requirements. When the vacuum pump is running, the oil level should reach the oil mark.
Maintenance and upkeep
1. The motor of the XGB-7500 vortex air pump is directly connected to the impeller and belongs to high-speed operation. The bearings need to be regularly lubricated with butter to prevent damage.
2. The shaft power of the motor is proportional to the pressure. To prevent the power from being too high due to long-term pressure and overloading the motor, a pressure relief valve is often used. It is a unloading valve. When the operating pressure of the high-pressure fan exceeds the set pressure of the pressure relief valve, the pressure relief valve will automatically open to release the excess pressure, thereby protecting the motor of the high-pressure fan.
3. The internal structure of the high-pressure fan is relatively compact, and the clearance between the impeller and the casing is very small, so impurities and dust must be filtered out. For impurities, a fine filter screen is usually installed at the air inlet. For dust, filters are often used. According to different use sites, different filter cores with different filtration precision are used. Different filter cores have different maintenance methods, which need to be clarified when placing an order.

XFC-1100 vortex air pump features
1. Ultra-quiet, no noise: Adopts advanced German technology. The motor runs directly, and with the addition of an integrated sound-damping device, the problem of high noise of high-pressure fans is improved, achieving a quiet effect.
2. High reliability. The machine can still operate when the usage conditions change. Except for the impeller, there are no other moving parts in the high-pressure blower, so the reliability is very high and it is almost maintenance-free. Precision outer bearings that are durable and have good heat dissipation are used, so it has the following advantages: high compression ratio; low bearing operating temperature; long service life of lubricating grease; maintenance-free.
3. Easy to install and fully equipped. It can be installed and put into use at any time, used for compressed air or vacuum pumping, and can also be installed in any horizontal or vertical direction.
4. Oil-free and pollution-free. When the impeller rotates, it does not come into contact with other parts, so no lubrication is needed, thus ensuring no pollution.
5. High quality. With 17 years of manufacturing experience, precise mechanical design and careful matching of motors with standard instrument testing, all parts can meet high-quality requirements. The standard IP54, F-class motor has high efficiency and few failures. There is a shaft seal between the motor and the blower to prevent foreign matter from entering. At the same time, to ensure functionality, every blower has undergone strict testing before leaving the factory.
Scope of application

XFC-1100 vortex air pump is suitable for environmental protection engineering, industrial machinery, plastic machinery, printing machinery (screen printing machines), photographic plate making, PCB equipment, electrical equipment, medical equipment, various burners, boilers, environmental protection aquaculture and so on