ROP-13A oil pump

The golden nine and silver ten are approaching, and various enterprises are constantly launching new products and showing their sincerity, all aiming to get a share of the sales volume. Among them, it is not difficult to find that some traditional enterprises still cannot let go of their pride, which is destined to be rejected by consumers with their feet and gradually withdraw from the market competition. However, the market is so fierce that enterprises that cannot let go of their pride will gradually do so in the future. If they do not let go, they will withdraw from the Chinese market. At present, the Chinese market is huge, and giving up means being eliminated by the market.
Since products are produced, there must be customers who need them, just in different quantities. Therefore, we should take every product and every customer seriously, so that our business path will get longer and longer.

Maintenance of ROP-10A Weiliang Oil Pump 1. Add grease regularly. The electric barrel pump runs at high speed, and the grease is easy to volatilize. Therefore, the lubrication at the bearing must be kept clean, and attention should be paid to replenishing and replacing the grease. 2. Conduct regular inspection and maintenance on the gear oil pump. For the electric barrel pump, regular inspection and maintenance shall be carried out. Check whether the power cord, internal wiring, plug and switch are in good condition, whether the insulation resistance is normal, whether the brush holder is loose, whether the commutator is in good contact with the brush, whether the armature winding and stator winding have open circuit faults, and whether the bearings and rotating parts are damaged, etc. 3. Keep all parts properly and replace with identical parts. When disassembling and inspecting the gear oil pump, each part should be stored properly. Special attention should be paid to not damaging or roughening the explosion-proof surface of explosion-proof parts, including insulating gaskets and sleeves. If any part is damaged, it must be replaced with a new identical part. Substitute materials with lower performance than the original materials or parts that do not meet the original specifications shall not be used. When assembling, all parts shall be installed in their original positions without omission. 4. Pay attention to the insulation resistance. Before using the electric liquid pump that has been left unused for a long time or used in a humid environment, use a 500V megohmmeter to measure the insulation resistance of the winding. If the insulation resistance between the winding and the motor housing is less than 7 megohms, the winding must be dried. 5. Store the electric oil pump in a dry, clean and non-corrosive gas environment.
The ROP-13A oil pump is a commonly used hydraulic oil pump, mainly used to transport various hydraulic oils. When using and maintaining the gear oil pump, we need to pay attention to its safety operation procedures and maintenance regulations to ensure the effective operation of the gear oil pump and extend its service life. This article will introduce the relevant contents of the safety operation and maintenance regulations of the gear oil pump. 2. Safety Operation Regulations of Gear Oil Pump Environmental Preparation 1. The ambient temperature should be controlled between -30℃ and +50℃. 2. The use site should be dry, and it is forbidden to use it in humid places with corrosive gases. 3. The use site should be well ventilated, and it is forbidden to use it in enclosed places. Preparations Before Using the ROP-13A Oil Pump 1. Confirm the model, flow rate, pressure range and corresponding pipeline layout of the gear oil pump before use. 2. The pipelines should be matched with the gear oil pump and hydraulic cylinder, and connected correctly. 3. If a time-sharing electrical appliance is used, check the electrical control box to ensure its normal operation. Operations Before and After Startup 1. Carefully check whether the connection between the gear oil pump and the pipeline is loose or leaking before starting. 2. When starting, first turn on the main power switch, then press the start button. 3. Immediately check whether the hydraulic cylinder is working normally after the gear oil pump starts. 4. After stopping use, first cut off the power of the gear oil pump, then stop its operation, and clean the surface of the gear oil pump and the pipelines. Safety Precautions 1. When using the ROP-13A oil pump, strictly follow the regulations, and use it when there are no people nearby. 2. The installation, adjustment and maintenance of the gear oil pump shall be completed by professional and technical personnel. 3. Keep the gear oil pump clean during use to prevent debris from entering the interior of the oil pump. 4. Use protective measures in the pipeline leading to the gear oil pump. 5. It is forbidden to adjust the pipeline while the gear oil pump is working, so as to avoid danger. 6. Do not disassemble or replace parts during the operation of the gear oil pump. Internal Maintenance 1. Clean the interior of the ROP-13A oil pump with clean hydraulic oil or clean water after each use, so as to remove oil stains or dust in it. 2. Regularly check the tightness of the interior of the gear oil pump, and replace damaged seals in time. 3. Regularly check the quality of the hydraulic oil inside the gear oil pump, and replace the hydraulic oil regularly according to the specified replacement cycle and suitable oil products. External Maintenance 1. Regularly clean the surface of the oil pump and the connecting pipelines to keep its appearance clean. 2. Regularly check the fastening status of the bolts, nuts and connecting parts of the oil pump, and adjust or replace them in time. 3. Regularly check whether the electrical components of the oil pump, such as circuit breakers, fuses, contactors, etc., are damaged, and replace them in time.