Wholesale of Santak batteries C12-100/12v100Ah batteries

Basic Parameters 2 Model: C12-100. Rated Voltage: 12V. Rated Capacity: 100Ah. Dimensions: Length × Width × Height is 328×172×220mm. Weight: Approximately 30.5kg. Charging Temperature: 0-45°C. Discharging Temperature: -20-60°C. Maximum Discharge Current: 1500A (5 seconds). Cycle Life: ≥750 cycles (70% DOD). Performance Features Excellent safety performance: Absorbed glass mat (AGM) design with no free-flowing electrolyte inside, no liquid leakage during normal use, and can operate normally even when tilted 90 degrees; Valve-regulated sealed structure, the safety valve automatically opens to release pressure when the internal air pressure is too high, with less accumulation of internal combustible gas, so it has good explosion-proof performance3. Excellent maintenance-free performance: Adopting the cathode absorption sealed maintenance-free principle, the gas sealing composite efficiency exceeds 95%, with very little water loss during normal use, no regular fluid replenishment maintenance is required3. Green and environmentally friendly: No acid mist during normal charging, will not pollute the computer room environment or corrode computer room equipment3. Low self-discharge: Using Pb-Ca-Sn alloy with high gas evolution potential, it can be put into normal use without recharging after being placed in a dry environment at 20°C for half a year3. Wide applicable ambient temperature: Can operate stably at -10℃-45℃3. Good high-current discharge resistance: Tight assembly process with low internal resistance, can discharge at 3 times the rated capacity current for 3 minutes or 6 times the rated capacity current for 5 seconds without any abnormality3. Long service life: Using high-purity raw materials, long-life formula and battery pack consistency control process, the normal floating charge design life can reach 7-10 years (≥38Ah)3. Good battery pack consistency: Control from the source such as grid plates and coating weight, weigh and grade the plates before final assembly, quantitatively inject acid, adopt the four-charge and three-discharge formation process, match the batteries through discharge before leaving the factory, and conduct static detection and secondary matching before leaving the warehouse to ensure the consistency of discharge and floating charge of the battery pack3. Structural Design Grid structure: Mid-position lugs and bottom corner staggered design, the bottom of the positive plates of the 2V series is covered with plastic protective films, the alloy is lead-calcium-tin aluminum alloy, the negative plates have high hydrogen evolution potential, the positive plate alloy is high-tin low-calcium alloy, with fine and dense organizational grains and good corrosion resistance14. Separator: Imported corrugated PVC separator specially used for gel batteries, with high porosity and low resistance14. Battery tank and cover: Made of ABS material, sealed with epoxy resin to ensure no leakage14. Terminal posts: Made of pure lead material with good corrosion resistance, the terminal posts and battery cover adopt a pressure ring structure, and then bonded with resin sealant to ensure sealing reliability14. Gas filtration and explosion-proof sheet device: All 2V and 12V series batteries are equipped with this device, which can prevent external open flames from igniting the battery, and filter out the precipitated gas to avoid environmental pollution14. Application Fields Uninterruptible Power Supply (UPS): In environments with unstable power supply, it can effectively ensure the normal operation of the system, providing backup power support for equipment such as computers and servers2. Solar energy storage system: Can be combined with solar power generation systems to store excess electricity for use at night or on rainy days, improving the utilization rate of solar power generation2. Communication facilities: Used for emergency power supply of base stations and other communication equipment, ensuring that the communication network can operate normally during power outages and other situations2. Emergency power supply: Provide fast and effective power support for emergency lighting, fire-fighting equipment and other items in emergency events such as fires and earthquakes2. Power tools and equipment: Provide powerful power support in occasions requiring mobile electricity, such as electric bicycles, electric forklifts and so on2. Medical equipment and instruments: Provide stable power for medical equipment such as ventilators and monitors, ensuring the normal progress of medical work1. DC power supply for power plants and hydropower stations: Provide DC power for control equipment and protection devices of power plants and hydropower stations, ensuring the safe and stable operation of the power system