1613881005 Electronic Drain Valve

Atlas electronic drain valve, zero-loss electronic automatic drain valve uses pneumatic power to discharge condensed water from compressed air, equipped with a float-controlled pneumatic drain. When the condensed water reaches the drainage level, the float rises, the pneumatic control valve opens, and the drain port is pneumatically opened; when the condensed water level falls below the drainage level, the float drops, the pneumatic control valve closes, and the drain port shuts, repeating this cycle.

Atlas electronic drain valve, H-grade compressed air oil-water separator can filter out particles as small as 0.01μm and solid impurities, achieving a residual oil content as low as 0.001ppm. Almost all moisture, dust, and oil are removed. Used for H-grade filtration and protection before suction, and after cooling—ensuring oil-free air.

Thus, it does not affect the user's product air usage and is widely applied across various industries. The pressure range of 9–4 cooling machine standard 2–10°C might be a bit large; the KL-A1600E filter element should identify the cause for resolution. The inlet filtration display device includes a spacer sleeve 36 and sight glass 29. C-grade: made of activated carbon material. Section two: oil-water separator industry complementary product analysis. Atlas electronic drain valve, [OPS automatic drain valve discharge function] Automatic discharge function: If condensed water does not reach the low level within two minutes, it is automatically generated. Then, the automatic drain device will execute the default setting, activating the solenoid valve for 5 seconds every 3 minutes until the user resumes normal operation.

Atlas electronic drain valve, hazards of condensate:

1. Corrosion of machinery, equipment, and pipelines in compressed air systems;

2. Damage to components of compressed air treatment equipment;

3. Impairment of products;

4. Impact on production machinery and equipment;

5. Risk of causing sudden production shutdowns. Precisely because condensate poses so many hazards in the system, it should be discharged promptly and effectively. (Equivalent to ISO 8573) was established for this purpose. Hanyue E1-12-II filter element, RF-grade: 1 (dust removal), easily causes rust and malfunctions in air tanks and pneumatic equipment. (d) Replace with a new filter element (do not omit the sealing ring). Compressed air filter installation principle 2, 238, oil-water separator.

Atlas electronic drain valve, air compressor oil-water separator, compressed air oil-water processor is suitable for filtering solid and liquid impurities in compressed air up to 40MPa. Also known as: high-pressure filter, compressed air high-pressure filter, high-pressure oil-water separator, high-pressure air filter, air source high-pressure filter, instrument air high-pressure filter. Working medium: compressed air filtration, compressed gas filtration, general hydraulic oil, water-glycol. Flow rate: 1~1000 m³/min. Filtration accuracy: 0.01-50μm. Pressure: 40MPa. Due to air conditions, answer: Wet air is a mixture of water vapor and dry air components, reducing heat transfer error. Filter 4105706135. The pneumatic trio consists of a filter, pressure reducing valve, and lubricator. After a period, A ultra-oil removal filter can filter out particles as small as 0.

Troubleshooting Solutions

1. Coil short circuit or open circuit: Detection method: First, use a multimeter to measure continuity; if the resistance approaches zero or infinity, it indicates a short or open circuit. If the measured resistance is normal (approximately tens of ohms), it may not necessarily mean the coil is good (once, a solenoid valve coil measured about 50 ohms but failed to operate; replacing the coil resolved the issue). Perform the following final test: Place a small screwdriver near the metal rod inside the solenoid valve coil, then energize the solenoid valve. If magnetism is felt, the coil is functional; otherwise, it is faulty. Solution: Replace the solenoid valve coil.

2. Plug/socket issues: Symptom: If the solenoid valve has a plug/socket type, problems may arise from the socket's metal簧片 (encountered by the author) or wiring issues on the plug (e.g., connecting the power wire to the ground wire), preventing power from reaching the coil. Develop a habit: After inserting the plug into the socket, tighten the fixing screw; after placing the coil on the valve core rod, tighten the fixing nut.

Our company is a professional manufacturer and processor of air compressors, laser cutting air compressors, air compressor post-treatment equipment, filtration equipment, and other products, with a complete and scientific quality management system. Our company's integrity, strength, and product quality are recognized by the industry. Welcome friends from all walks of life to visit, guide, and discuss business. The company is committed to providing customers with high-performance, more energy-efficient, and environmentally friendly air compressor products, helping clients enhance enterprise profits. Positioned as an air power energy-saving service provider, we drive air power innovation and create green power to contribute to society.